This makes it ideally suited for use in heterogeneous or convergent industrial networks. The PROmesh P10 was especially designed for the application in Gigabit and/or TSN networks. Gigabit-capable (1000 / 2500 Mbps) / TSN ready The PROmesh P10 is developed on the basis of the PROFINET specification V 2.4 and certified according to the following points: This means that both manufacturers and users can implement the advantages of TSN, such as future-proof IEEE Ethernet technology with higher bandwidth, deterministics, flexible network configuration, and a wide variety of chips, interoperably. Since 2020, PROFINET has been available via TSN with the PROFINET specification V 2.4. However, practice shows that the real voltage supply deviates from the required tolerance range and devices fail due to the large distribution depth. For this reason, the PROmesh P10 has an integrated monitoring of the power supply (24 V), which can be integrated into the central network monitoring as an additional stability parameter.Īccording to EN 61131-2, a tolerance range of -17.5 % to +16.5 % must be maintained for a 24 V power supply for safe PLC operation. A switch failure due to insufficient power supply is not tolerable. Industrial switches form the central hub of any network. This can be called up via the web interface of the switch. To simplify subsequent analysis, an exact time history around the incident ( snapshot) is also stored. If a freely settable limit value is exceeded, an automatic alarm notification is triggered. With the aid of permanent leakage current monitoring, common sources of EMC interference can be identified without complicated measuring procedures.įor this purpose the PROmesh P10 captures the exact time, frequency and intensity of occurring EMC disturbances. EMC monitoringĭespite correct shielding, EMC couplings on data cables frequently cause communication errors or breakdowns. This displays to the second all network loads per port and the associated failures and makes it possible to identify and eliminate network load-related bottlenecks. In order to make this short-term peak load visible, the PROmesh P10 provides useful network load statistics.
due to acyclic queries from the IT level or TCP/IP applications. This is often caused by sporadically occurring network load peaks, e.g.
If the data traffic in the network exceeds the performance limit of a switch, data loss (discards) occurs. All alarms can also be transmitted to a higher-level network monitoring system (via SNMP, PROFINET, email, relay). Damaged cables can be replaced according to their condition during the next maintenance interval. Thanks to the traffic light colour principle, it is possible to immediately detect when the value falls below the preset threshold value. The status of each data cable can be easily checked via the integrated web interface of the PROmesh P10. As a result, the line status per port can be determined. This status value is compared to a "Q-setpoint value" that corresponds to the cable length. In order to visualise the physical abrasion of network cables, a quality value "Q-actual value" is permanently determined for each cable. – Detect and rectify line-based defects at an early stageĭue to a sophisticated evaluation system of the transmission and reception parameters, the PROmesh P10 switch is able to provide clear statements about the current transmission quality and also about the state of the data lines. Online cable diagnostics (during operation)
#Proscan client where to set com port download#
Please refer to our download area or the product details for the complete data sheet. HTTP, SNMPv1, SNMPv2, DHCP Client, TFTP, Syslog, LLDP, IGMP, SMTP Client, SNTP Client, RSTP, MRP Master/Client PROmesh P10 – PROFINET/Industrial Ethernet Switch In short: Be able to make a well-founded statement about the "wear reserve" of the network at any time - without interrupting plant operation. With this knowledge maintenance measures become more predictable.ĭiscover the web interface and functions of the PROmesh P10/P10X Therefore, it is suitable for line testing during commissioning and during plant operation. The PROmesh P10 industrial switch, from the latest Gigabit switch generation, has an integrated cable diagnosis, which satisfies both the requirements of cable measurement and permanent, qualitative cable monitoring. The PROmesh P10 provides an alternative to this complex procedure for the first time. Until now, this testing had to be accomplished in a separate work step. Hen installing PROFINET networks in machines and plants, connecting cables must be tested for proper function or even be certified. With integrated cable diagnostics and extensive monitoring.
0 kommentar(er)
